สยามฟิชชิ่ง
หน้าแรก|กระดาน|รีวิว|ประมูล|ตลาด|เปิดท้าย
login | สมัครสมาชิก | วิธีสมัครสมาชิก | ลืมชื่อ/รหัส | login ไม่ได้? | 29 มี.ค. 67
Shimano Cardiff : Fishing Reel Inside
 ห้องผ่ารอก > วิธีผ่า/ล้าง/ซ่อม
ความเห็น: 12 - [20 ก.ค. 57, 23:29] ดู: 19,512 - [28 มี.ค. 67, 20:55] โหวต: 3
Shimano Cardiff
luzifer (228 คะแนนโหวตจากผู้ชมกระทู้) offline
6 มี.ค. 51, 02:14
1
Shimano Cardiff
ภาพที่ 1
Tools

(ไปเจอมาจากเวปต่างประเทศนะครับ)
Shimano Cardiff
ภาพที่ 2
1) Remove the handle side plate assembly from the frame. This is done be removing the 3 side plate screws. (See fig 1)

(แปลกันเองนะครับ ผมก็ดูแค่รูป 555)
Shimano Cardiff
ภาพที่ 3
2) Remove the handle nut, handle nut lock plate and Phillips head screw (See fig 2)

3) Remove the drag star assembly
Shimano Cardiff
ภาพที่ 4
4) Remove the drag pressure washers (4) Pay attention to the arrangement of the washers (See fig 3)
Shimano Cardiff
ภาพที่ 5
5) Remove the 2 Phillips head screws from the side plate assembly (See fig 4)
Shimano Cardiff
ภาพที่ 6
6) Remove the side plate assembly from the set plate (black plastic assembly housing the gears and clutch) See fig 5

7) Remove the 2 yoke springs

(ทำไมรูปมันแหว่งๆ???)
Shimano Cardiff
ภาพที่ 7
8) Remove the pinion gear and yoke assembly (See fig 6)

9) Remove the main gear assembly
Shimano Cardiff
ภาพที่ 8
10) Remove the anti reverse ratchet and assist stopper pawl. Inspect assist stopper pawl for damage. If damaged the anti reverse bearing has failed and will need replacement. (See fig 7)
Shimano Cardiff
ภาพที่ 9
11) Clean the set plate assembly of all excess grease and dirt. (See fig 8)
Shimano Cardiff
ภาพที่ 10
12) Remove all the drag washers paying attention to the order they are stacked. (See fig 9)

13) Using an old toothbrush clean all grease from the teeth of the main gear.

14) Apply Shimano grease to approximately one half of the teeth on the main gear.

15) Carefully wipe all excess grease from the drag washers. Apply a light coating of grease between your thumb and index finger. Lightly (emphasis on lightly) apply grease to both sides of the drag washers.

16) Using the toothbrush clean the teeth of the pinion gear.

(นี่ก็แหว่ง) -*-
Shimano Cardiff
ภาพที่ 11
17) Remove some cotton from one end of a Q-tip and dip in alcohol. Run it through the middle of the pinion gear to remove all oil/grease and dirt. (See fig 10)

18) Clean all excess grease from the yoke assembly
Shimano Cardiff
ภาพที่ 12
19) Using Q-tips and alcohol clean the spool shaft and spool lips. (See figures 11 & 12)
Shimano Cardiff
ภาพที่ 13
*-*
Shimano Cardiff
ภาพที่ 14
20) Using Q-tips and alcohol, clean the spool raceways on the frame (See figures 13 & 14)
Shimano Cardiff
ภาพที่ 15
21) Apply a small drop of oil to the spool shaft bearing.
Shimano Cardiff
ภาพที่ 16
22) Clean all excess grease from the worm gear (level wind gear) See fig 15
Shimano Cardiff
ภาพที่ 17
23) Clean line guide eyelet with a Q-tip and alcohol. (See fig 16)

24) Apply oil to the worm gear. One drop at each end and one or two drops in the middle.
Shimano Cardiff
ภาพที่ 18
25) Clean all excess grease from idle gear and bearing. Apply one drop of oil to the bearing. (See fig 17)

26) Reassemble the reel and check performance. Tip When installing the handle side plate back onto the frame make sure the thumb bar is in the up position. If not the clutch (thumb bar) will not work correctly.
Shimano Cardiff
ภาพที่ 19
จบแล้วคร๊าบบบ

Thanks.

www.calfishing.com

* ปล. หน้าของWebsite จะมีDiagram รอกให้ชมกันด้วยนะครับ (CDF100-101,CDF200-201,CDF300-301,CDF400-401)

สวัสดี *-*
กรุณา ลงทะเบียน และ login ก่อนส่งความเห็นครับ
siamfishing.com © 2024